{"product_id":"hearthstone-stoves-heritage-freestanding-wood-stove","title":"Hearthstone Stoves Heritage Freestanding Wood Stove","description":"\u003ch2\u003eSoapstone-Lined Cast Iron with TruHybrid™ Catalytic Combustion and a Side Load Door\u003c\/h2\u003e\n\u003cp\u003eFull cast iron construction with 1¼\" soapstone lining, TruHybrid™ catalytic combustion, a side load door, and a published HeatLife™ of up to 25 hours.\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTruHybrid™ combustion system combining primary and secondary combustion with catalytic tertiary combustion\u003c\/li\u003e\n\u003cli\u003eEPA certified at 1.1 g\/hr particulate emissions under the 2020 EPA particulate standard, tested with crib wood\u003c\/li\u003e\n\u003cli\u003e77.3% HHV weighted-average efficiency, measured across four burn-rate categories using EPA Method 28R and CSA B415-10 methodology\u003c\/li\u003e\n\u003cli\u003ePublished HeatLife™ of up to 25+ hours and burn time of up to 20+ hours, depending on wood, draft, and operating conditions\u003c\/li\u003e\n\u003cli\u003eFull cast iron construction with 1¼\" soapstone lining for gradual radiant heat\u003c\/li\u003e\n\u003cli\u003eSide load door, ordered in a left-loading or right-loading configuration\u003c\/li\u003e\n\u003cli\u003eHeats up to a maximum of 2,000 square feet, depending on insulation, floor plan, stove placement, and fuel quality\u003c\/li\u003e\n\u003cli\u003eFour current finishes: Matte Black, Brown Enamel, Black Enamel, and Seafoam Enamel\u003c\/li\u003e\n\u003cli\u003e6\" flue collar with top or rear exit, and approval for mobile home installation when installed to the manufacturer's requirements\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n\u003ch4\u003eTruHybrid™ Combustion Technology\u003c\/h4\u003e\n\u003cp\u003eThe TruHybrid™ system burns the fuel, then the gases the wood releases, then routes the remaining exhaust through a catalyst for tertiary combustion. A bypass handle directs combustion products around the catalyst during startup and reloading, and through the catalyst once the catalyst probe shows the stove is in its active range. The Heritage uses two Applied Ceramics ACI-6M2 catalytic combustors, which require periodic inspection and eventual replacement.\u003c\/p\u003e\n\u003ch4\u003eSoapstone and Cast Iron Construction\u003c\/h4\u003e\n\u003cp\u003eThe Heritage is built with full cast iron construction and a 1¼\" soapstone lining. Soapstone absorbs the heat of the fire and releases it gradually, warming objects in the room rather than only the air. HearthStone notes that soapstone requires gradual break-in fires so the natural moisture in the freshly quarried stone is driven out slowly, and that stone color may change and surface fractures may appear with use without affecting stove function.\u003c\/p\u003e\n\u003ch4\u003eSide-Loading Convenience\u003c\/h4\u003e\n\u003cp\u003eWood is loaded through the side door as well as the front, and the Heritage is ordered as either a left-loading or right-loading stove. The loading side affects hearth pad layout, so it should be selected against the intended installation. The optional Side Door Lock Kit reduces the minimum required hearth pad width.\u003c\/p\u003e\n\u003ch4\u003eCast Iron and Enamel Finishes\u003c\/h4\u003e\n\u003cp\u003eThe Heritage is offered in Matte Black and in Brown, Black, and Seafoam porcelain enamel. Enamel finishes are covered against peeling or fading for one year under the HearthStone limited warranty, and replacement stones and enameled parts are drawn from current stock and may vary from originals in color, grain, or pattern.\u003c\/p\u003e\n\u003ch4\u003eFire Viewing and Everyday Operation\u003c\/h4\u003e\n\u003cp\u003eA large glass window lets the fire be seen from a variety of locations in the room. A single primary air lever below the ash lip regulates the burn rate, the bypass handle controls catalyst engagement, and a catalyst probe shows when the stove is in its active temperature range, typically 800°F to 1300°F. An optional ash pan with a shaker grate allows ash removal without shoveling through the front door.\u003c\/p\u003e\n\u003ch4\u003eHeating Performance\u003c\/h4\u003e\n\u003cp\u003eHearthStone publishes a heating area of up to a maximum of 2,000 square feet and output of up to 60,000 BTU. Under EPA test conditions with Douglas fir test wood, the Heritage 8024 delivered heat at rates ranging from 12,889 to 29,191 BTU\/hr. HearthStone states in the current owner's manual that the Heritage 8024 should not be considered the primary heat source for a home, and that factors unique to a given house can reduce the square footage the stove will heat.\u003c\/p\u003e\n\u003ch3\u003eAvailable Finishes and Loading Configurations\u003c\/h3\u003e\n\u003cp\u003eThe Heritage 8024 is built in both left-loading and right-loading versions, and every finish is available in either loading configuration. Pricing varies by finish rather than by loading side.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003cth\u003eLoading Configuration\u003c\/th\u003e\n\u003cth\u003ePart ID\u003c\/th\u003e\n\u003cth\u003eMSRP\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlack Matte\u003c\/td\u003e\n\u003ctd\u003eLeft Load\u003c\/td\u003e\n\u003ctd\u003e8024-4110L\u003c\/td\u003e\n\u003ctd\u003e$4,999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlack Matte\u003c\/td\u003e\n\u003ctd\u003eRight Load\u003c\/td\u003e\n\u003ctd\u003e8024-4110R\u003c\/td\u003e\n\u003ctd\u003e$4,999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrown Enamel\u003c\/td\u003e\n\u003ctd\u003eLeft Load\u003c\/td\u003e\n\u003ctd\u003e8024-4120L\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrown Enamel\u003c\/td\u003e\n\u003ctd\u003eRight Load\u003c\/td\u003e\n\u003ctd\u003e8024-4120R\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlack Enamel\u003c\/td\u003e\n\u003ctd\u003eLeft Load\u003c\/td\u003e\n\u003ctd\u003e8024-4150L\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlack Enamel\u003c\/td\u003e\n\u003ctd\u003eRight Load\u003c\/td\u003e\n\u003ctd\u003e8024-4150R\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeafoam Enamel\u003c\/td\u003e\n\u003ctd\u003eLeft Load\u003c\/td\u003e\n\u003ctd\u003e8024-4161L\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeafoam Enamel\u003c\/td\u003e\n\u003ctd\u003eRight Load\u003c\/td\u003e\n\u003ctd\u003e8024-4161R\u003c\/td\u003e\n\u003ctd\u003e$5,799\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003ePricing notice:\u003c\/strong\u003e Prices shown are current manufacturer-suggested retail prices for the stove in the selected finish and loading configuration. Chimney components, hearth protection, accessories, delivery, installation, and applicable taxes are additional.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ch4\u003ePerformance\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003e8024\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCombustion system\u003c\/th\u003e\n\u003ctd\u003eTruHybrid™ — primary, secondary, and catalytic tertiary combustion\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCatalytic combustor\u003c\/th\u003e\n\u003ctd\u003eApplied Ceramics ACI-6M2, two required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeating area\u003c\/th\u003e\n\u003ctd\u003eUp to a maximum of 2,000 sq ft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePublished heat output\u003c\/th\u003e\n\u003ctd\u003eUp to 60,000 BTU\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTested heat output range\u003c\/th\u003e\n\u003ctd\u003e12,889 to 29,191 BTU\/hr under specific test conditions using Douglas fir test wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBurn time\u003c\/th\u003e\n\u003ctd\u003eUp to 20+ hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeatLife™\u003c\/th\u003e\n\u003ctd\u003eUp to 25+ hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCatalyst operating range\u003c\/th\u003e\n\u003ctd\u003eTypically 800°F to 1300°F\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eFirebox and Fuel\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFuel type\u003c\/th\u003e\n\u003ctd\u003eNatural cordwood only\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFirebox capacity\u003c\/th\u003e\n\u003ctd\u003e2.2 cu ft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum log length\u003c\/th\u003e\n\u003ctd\u003eUp to 21\" (53.3 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSide load door\u003c\/th\u003e\n\u003ctd\u003eLeft or right, specified at time of order\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAsh pan\u003c\/th\u003e\n\u003ctd\u003eOptional, kit 90-54240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eDimensions and Weight\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e28⅛\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDepth\u003c\/th\u003e\n\u003ctd\u003e21⅝\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeight\u003c\/th\u003e\n\u003ctd\u003e30¼\" (76.9 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e580 lbs (263 kg)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDoor glass\u003c\/th\u003e\n\u003ctd\u003e5 mm x 287 mm x 457 mm ceramic IR or Neoceram IR, replacement glass kit 90-58215\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCrate dimensions\u003c\/th\u003e\n\u003ctd\u003eH 39\" x W 29\" x L 36\" (99 x 73.7 x 91.5 cm), add 4\" (10.2 cm) for pallet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eFlue and Installation\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFlue exit location\u003c\/th\u003e\n\u003ctd\u003eTop or rear; rear exit requires the top-to-rear venting conversion described in the owner's manual\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlue collar and connector size\u003c\/th\u003e\n\u003ctd\u003e6\" (152 mm) diameter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMetal chimney requirement\u003c\/th\u003e\n\u003ctd\u003e6\" (152 mm) inside diameter, listed Type HT (2100°F) per UL 103 or ULC S629\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMasonry chimney requirement\u003c\/th\u003e\n\u003ctd\u003eCode-approved lined chimney, 6\" (152 mm) round flue or 8\" x 8\" (203 x 203 mm) square flue\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecommended minimum chimney height, top exit\u003c\/th\u003e\n\u003ctd\u003e16 feet (4.9 m) off the floor, or 13 feet 5¾\" (4.1 m) from the top of the stove\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecommended minimum chimney height, rear exit\u003c\/th\u003e\n\u003ctd\u003e19 feet (5.8 m) off the floor, or 16 feet 5¾\" (5.0 m) from the top of the stove\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecommended maximum chimney height\u003c\/th\u003e\n\u003ctd\u003e30 feet (9 m)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRequired draft\u003c\/th\u003e\n\u003ctd\u003e0.06\" to 0.1\" water column; drafts above 0.1\" WC require a stovepipe damper\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutside air connection\u003c\/th\u003e\n\u003ctd\u003eOptional kit 90-53220, minimum 3\" (76 mm) diameter duct supplied by others\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMobile home approval\u003c\/th\u003e\n\u003ctd\u003eApproved when installed per 24 CFR Part 3280; outside air kit, floor anchoring, and a listed mobile home chimney and connector kit are required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eEfficiency, Emissions, and Certification\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eHHV efficiency\u003c\/th\u003e\n\u003ctd\u003e77.3% weighted average across four burn-rate categories, measured using EPA Method 28R and CSA B415-10 methodology\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eParticulate emissions\u003c\/th\u003e\n\u003ctd\u003e1.1 g\/hr\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEPA certification\u003c\/th\u003e\n\u003ctd\u003eCertified to comply with the U.S. EPA 2020 particulate emissions standard, tested to EPA Method 28R, 40 CFR Part 60, using crib wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEPA file number\u003c\/th\u003e\n\u003ctd\u003eF18-307\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCO emissions by burn category\u003c\/th\u003e\n\u003ctd\u003eCategory 1 (low) 0.11 g\/min, Category 2 (medium low) 0.25 g\/min, Category 3 (medium high) 0.10 g\/min, Category 4 4.12 g\/min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTested standards\u003c\/th\u003e\n\u003ctd\u003eConforms to UL Std. 1482-2022; certified to ULC Std. S627-2023\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eClearances and Hearth Requirements\u003c\/h3\u003e\n\u003cp\u003eThe values below are from the current Heritage 8024 owner's and installation manual. Reduced clearances require the HearthStone rear heat shield, kit 90-68210, and listed close-clearance connector pipe. Double-wall connector figures shown by HearthStone are specific to Simpson Dura-Vent DVL and may vary with other brands.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Clearance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eSide\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eCorner installation\u003c\/td\u003e\n\u003ctd\u003e8\" (21 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eSide\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e10\" (26 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eCorner installation\u003c\/td\u003e\n\u003ctd\u003e8\" (21 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDouble-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eSide\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDouble-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e6\" (15 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDouble-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eCorner installation\u003c\/td\u003e\n\u003ctd\u003e8\" (21 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eCorner clearances account for clearance of combustibles to the body of the stove only. Minimum hearth pad dimensions must still be maintained and may result in larger distances to the actual combustible surfaces. Canadian installations require additional clearance for several of these measurements; refer to the current manual for the Canadian figures.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAlcove installation, unprotected surfaces\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Clearance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMinimum alcove width\u003c\/td\u003e\n\u003ctd\u003e60½\" (154 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMinimum alcove side clearance\u003c\/td\u003e\n\u003ctd\u003e18\" (46 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMinimum alcove rear clearance\u003c\/td\u003e\n\u003ctd\u003e20\" (51 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eAlcove ceiling above stove top\u003c\/td\u003e\n\u003ctd\u003e33¾\" (86 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eAlcove ceiling above floor\u003c\/td\u003e\n\u003ctd\u003e64\" (163 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eHearth and floor protection\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCombustible flooring must be protected with a covering of noncombustible material. The Heritage 8024 does not require an insulated hearth pad and there is no R-value requirement; the requirement is ember protection. The dimensions below are measured from the body of the stove, not the legs, and extend beyond the stove as shown.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Floor Protection\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAll installations\u003c\/td\u003e\n\u003ctd\u003eSide load door side\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm) United States \/ 18\" (46 cm) Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAll installations\u003c\/td\u003e\n\u003ctd\u003eOpposite side\u003c\/td\u003e\n\u003ctd\u003e5\" (13 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAll installations\u003c\/td\u003e\n\u003ctd\u003eRear\u003c\/td\u003e\n\u003ctd\u003e2\" (5 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAll installations\u003c\/td\u003e\n\u003ctd\u003eFront\u003c\/td\u003e\n\u003ctd\u003e16\" (41 cm) United States \/ 18\" (46 cm) Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWith Side Door Lock Kit 90-70210 installed\u003c\/td\u003e\n\u003ctd\u003eMinimum hearth pad width\u003c\/td\u003e\n\u003ctd\u003e37\" (94 cm) United States \/ 40½\" (103 cm) Canada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eHearthStone notes that luxury vinyl plank and luxury vinyl tile flooring warrants extra consideration, as some products begin to warp at 110° Fahrenheit, and that additional shielding may be necessary depending on the flooring used.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation notice:\u003c\/strong\u003e Clearances and hearth requirements vary by connector type, shielding, loading-door orientation, and installation configuration. Refer to the current Heritage installation manual and applicable local requirements before installation.\u003c\/p\u003e\n\u003ch3\u003eIncluded Equipment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHeritage 8024 woodstove with catalytic combustors installed\u003c\/li\u003e\n\u003cli\u003eOwner's manual with installation and operating instructions\u003c\/li\u003e\n\u003cli\u003eWood door and bypass handles with screws and washers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Accessories\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eAccessory\u003c\/th\u003e\n\u003cth\u003ePart ID\u003c\/th\u003e\n\u003cth\u003eMSRP\u003c\/th\u003e\n\u003cth\u003eCompatibility or Requirement Note\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutside Air Starter\u003c\/td\u003e\n\u003ctd\u003e90-53220\u003c\/td\u003e\n\u003ctd\u003e$109\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlower\u003c\/td\u003e\n\u003ctd\u003e90-57210\u003c\/td\u003e\n\u003ctd\u003e$599\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield, Heritage, and Castleton. Requires a compatible rear heat shield.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAsh Pan\u003c\/td\u003e\n\u003ctd\u003e90-54240\u003c\/td\u003e\n\u003ctd\u003e$599\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear Heat Shield\u003c\/td\u003e\n\u003ctd\u003e90-68210\u003c\/td\u003e\n\u003ctd\u003e$129\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSide Door Lock Kit\u003c\/td\u003e\n\u003ctd\u003e90-70210\u003c\/td\u003e\n\u003ctd\u003e$89\u003c\/td\u003e\n\u003ctd\u003eFor Heritage.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eAll accessories listed above are optional and sold separately unless expressly stated otherwise. An outside air kit is required for mobile home installations.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eHearthStone warrants the appliance to the original retail purchaser only, when purchased by that purchaser and installed by an authorized HearthStone dealer or their designated representative, against defects in material or workmanship. Coverage begins on the date of the original invoice and is not transferable to subsequent owners.\u003c\/p\u003e\n\u003cp\u003eWarranty periods differ by component. HearthStone defines the term \"Limited Lifetime\" as 10 years from the beginning of warranty coverage, and applies it to the stone, to cast iron not listed elsewhere, and to the clean-burning air supply system. Door handles and latches and steel components and the firebox carry a 5-year period. Appliance electrical components carry a 2-year period. Enamel finish against peeling or fading, glass, the ash grate, accessories, and all components not listed elsewhere carry a 1-year period. The catalytic combustors are covered directly by the combustor manufacturer, Applied Ceramics, under a separate limited warranty that provides free replacement within two years of purchase and prorated replacement pricing thereafter.\u003c\/p\u003e\n\u003cp\u003eHearthStone pays for warranty labor performed by an authorized dealer during the first year after the purchase date only when the appliance was installed by an authorized dealer or their designated representative; otherwise, and thereafter, labor is the purchaser's responsibility. Exclusions include over-firing, improper installation or operation, service by anyone other than an authorized dealer, use of unapproved fuels or components, water and corrosion damage, and normal wear parts such as paint, gaskets, baffles, refractory materials, ash grates, and glass. Surface and hairline cracks and scratches in the stone that do not affect operation or safety are excluded, and HearthStone's obligation does not extend to the appliance's ability to heat a desired space. Warranty registration is not required as a condition of coverage. Refer to the complete warranty in the current Heritage 8024 owner's manual for the full terms, conditions, and limitations.\u003c\/p\u003e\n\u003ch3\u003eAbout HearthStone\u003c\/h3\u003e\n\u003cp\u003eHearthStone Quality Home Heating Products builds wood- and gas-burning hearth appliances in Morrisville, Vermont, and has been building industry-leading products since 1978. Its stoves are handcrafted by Vermont craftsmen from materials including heating-grade soapstone, cast iron produced at the company's own foundry in Spain, precision-made steel, and engineered ceramics, and every HearthStone soapstone stove is signed by the stove builder. The company's TruHybrid™ system, used across its current wood stove line, adds catalytic tertiary combustion to primary and secondary combustion.\u003c\/p\u003e","brand":"Hearthstone Stoves","offers":[{"title":"Default Title","offer_id":53462624010516,"sku":"8024","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0809\/9381\/2756\/files\/Heritage8024_blackenamel_200213.webp?v=1785544430","url":"https:\/\/cozyglowstoves.com\/products\/hearthstone-stoves-heritage-freestanding-wood-stove","provider":"Cozy Glow Stoves","version":"1.0","type":"link"}