{"product_id":"hearthstone-stoves-mansfield-freestanding-wood-stove","title":"Hearthstone Stoves Mansfield Freestanding Wood Stove","description":"\u003ch2\u003eHearthStone's Largest Soapstone Stove with TruHybrid™ Catalytic Combustion\u003c\/h2\u003e\n\u003cp\u003eFull cast iron construction with over 230 pounds of soapstone, TruHybrid™ catalytic combustion, a deep 21½\" x 20½\" firebox, and published burn times of up to 30+ hours.\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTruHybrid™ combustion system combining primary and secondary combustion with catalytic tertiary combustion\u003c\/li\u003e\n\u003cli\u003eEPA certified at 0.54 g\/hr particulate emissions under the 2020 EPA particulate standard, tested with crib wood\u003c\/li\u003e\n\u003cli\u003e77.7% HHV weighted-average efficiency, measured across four burn-rate categories using EPA Method 28R and CSA B415-10 methodology\u003c\/li\u003e\n\u003cli\u003ePublished burn time of up to 30+ hours, depending on wood, draft, and operating conditions\u003c\/li\u003e\n\u003cli\u003eHearthStone's largest soapstone stove, built with over 230 pounds of soapstone and full cast iron construction\u003c\/li\u003e\n\u003cli\u003eDeep 21½\" wide by 20½\" deep firebox accepts logs up to 21\" in length\u003c\/li\u003e\n\u003cli\u003eHeats up to a maximum of 2,500 square feet, depending on insulation, floor plan, stove placement, and fuel quality\u003c\/li\u003e\n\u003cli\u003eThree current finishes: Matte Black, Brown Enamel, and Seafoam Enamel\u003c\/li\u003e\n\u003cli\u003e6\" flue collar with top or rear exit, and approval for U.S. mobile home installation when installed to the manufacturer's requirements\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n\u003ch4\u003eTruHybrid™ Combustion Technology\u003c\/h4\u003e\n\u003cp\u003eThe TruHybrid™ system burns the fuel, then the gases the wood releases, then routes the remaining exhaust through the catalysts for tertiary combustion. A bypass handle directs combustion products around the catalysts during startup and reloading, and through the catalysts once the catalyst thermometer shows the stove is in its active range. The Mansfield uses Applied Ceramics ACI-6M2 catalytic combustors, three required, which require periodic inspection and eventual replacement. The Mansfield typically operates in the 450°F to 1200°F flue gas range, with the catalysts becoming active around 500°F.\u003c\/p\u003e\n\u003ch4\u003eSoapstone and Cast Iron Construction\u003c\/h4\u003e\n\u003cp\u003eThe Mansfield is HearthStone's largest soapstone stove, constructed with over 230 pounds of soapstone and full cast iron. Soapstone absorbs the heat of the fire and releases it gradually, warming objects in the room rather than only the air. HearthStone notes that soapstone requires gradual break-in fires so the natural moisture in the freshly quarried stone is driven out slowly, and that stone color may change and surface fractures may appear with use without affecting stove function.\u003c\/p\u003e\n\u003ch4\u003eDeep Firebox\u003c\/h4\u003e\n\u003cp\u003eThe 21½\" wide by 20½\" deep firebox provides space for building large fires, and accepts logs up to 21\" in length. HearthStone publishes a firebox capacity of 2.9 cubic feet in the current owner's manual.\u003c\/p\u003e\n\u003ch4\u003eFire Viewing and Everyday Operation\u003c\/h4\u003e\n\u003cp\u003eA large glass window lets the fire be seen from a variety of locations in the room. A single primary air lever below the ash lip regulates the burn rate, the bypass handle controls catalyst engagement, and a catalyst thermometer shows when the stove is in the active temperature range. An optional ash pan with a shaker grate allows ash removal without shoveling through the front door.\u003c\/p\u003e\n\u003ch4\u003eHeating Performance\u003c\/h4\u003e\n\u003cp\u003eHearthStone publishes a heating area of up to a maximum of 2,500 square feet and a maximum heat output of 80,000 BTU per hour of cordwood. Under EPA test conditions, the Mansfield 8013 delivered heat at rates ranging from 14,043 to 32,200 BTU (output). HearthStone states in the current owner's manual that the Mansfield should not be considered the primary heat source for a home, and that factors unique to a given house can reduce the square footage the stove will heat.\u003c\/p\u003e\n\u003ch3\u003eAvailable Finishes and Configurations\u003c\/h3\u003e\n\u003cp\u003eThe Mansfield 8013 is currently orderable in three finishes. Pricing varies by finish.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003cth\u003ePart ID\u003c\/th\u003e\n\u003cth\u003eMSRP\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlack Matte (polished stone, black matte cast)\u003c\/td\u003e\n\u003ctd\u003e8013-4110\u003c\/td\u003e\n\u003ctd\u003e$5,049\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrown Enamel (polished stone, brown enamel cast)\u003c\/td\u003e\n\u003ctd\u003e8013-4120\u003c\/td\u003e\n\u003ctd\u003e$5,699\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeafoam Enamel (polished stone, seafoam enamel cast)\u003c\/td\u003e\n\u003ctd\u003e8013-4161\u003c\/td\u003e\n\u003ctd\u003e$5,699\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003ePricing notice:\u003c\/strong\u003e Prices shown are current manufacturer-suggested retail prices for the stove in the selected finish. Chimney components, hearth protection, accessories, delivery, installation, and applicable taxes are additional.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ch4\u003ePerformance\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003e8013\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCombustion system\u003c\/th\u003e\n\u003ctd\u003eTruHybrid™ — primary, secondary, and catalytic tertiary combustion\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCatalytic combustor\u003c\/th\u003e\n\u003ctd\u003eApplied Ceramics ACI-6M2, three required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeating area\u003c\/th\u003e\n\u003ctd\u003eUp to a maximum of 2,500 sq ft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum heat output\u003c\/th\u003e\n\u003ctd\u003e80,000 BTU per hour of cordwood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTested heat output range\u003c\/th\u003e\n\u003ctd\u003e14,043 to 32,200 BTU (output) under specific test conditions\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBurn time\u003c\/th\u003e\n\u003ctd\u003eUp to 30+ hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeatLife™\u003c\/th\u003e\n\u003ctd\u003eUp to 20 hours, per the current owner's manual (revision 10\/21\/24)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTypical operating range\u003c\/th\u003e\n\u003ctd\u003e450°F to 1200°F flue gas temperature\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eFirebox and Fuel\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFuel type\u003c\/th\u003e\n\u003ctd\u003eNatural cordwood only\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFirebox capacity\u003c\/th\u003e\n\u003ctd\u003e2.9 cu ft (0.082 cubic meters)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFirebox size\u003c\/th\u003e\n\u003ctd\u003e21½\" wide x 20½\" deep\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum log length\u003c\/th\u003e\n\u003ctd\u003eUp to 21\" (54 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAsh pan\u003c\/th\u003e\n\u003ctd\u003eOptional, kit 90-54240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eDimensions and Weight\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eHeight\u003c\/th\u003e\n\u003ctd\u003e32\" (81 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e28\" (71 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDepth\u003c\/th\u003e\n\u003ctd\u003e24⅛\" (61 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e650 lbs (295 kg)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCrate dimensions\u003c\/th\u003e\n\u003ctd\u003eH 40\" x W 29.5\" x L 36\" (102 x 75 x 92 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eFlue and Installation\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFlue exit location\u003c\/th\u003e\n\u003ctd\u003eTop or rear; rear exit requires the flue collar and flue plate conversion described in the owner's manual\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFlue collar and connector size\u003c\/th\u003e\n\u003ctd\u003e6\" (152 mm) diameter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMetal chimney requirement\u003c\/th\u003e\n\u003ctd\u003e6\" (152 mm) inside diameter, listed Type HT (2100°F) per UL 103 or ULC S629\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMasonry chimney requirement\u003c\/th\u003e\n\u003ctd\u003eCode-approved lined chimney, 6\" (152 mm) round flue or 8\" x 8\" (203 x 203 mm) square flue\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecommended minimum chimney height, top exit\u003c\/th\u003e\n\u003ctd\u003e16 feet (4.9 m) off the floor, or 13 feet 5¾\" from the top of the stove\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMinimum chimney height, rear exit\u003c\/th\u003e\n\u003ctd\u003e15 feet minimum; 19 feet (5.8 m) off the floor recommended, or 16 feet 5¾\" from the top of the stove\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecommended maximum chimney height\u003c\/th\u003e\n\u003ctd\u003e30 feet (9 m)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRequired draft\u003c\/th\u003e\n\u003ctd\u003e0.06\" to 0.1\" water column; drafts above 0.1\" WC require a stovepipe damper; rear-exit venting requires adequate minimum draft, verified at installation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutside air connection\u003c\/th\u003e\n\u003ctd\u003eOptional kit 90-53220, minimum 3\" (76 mm) diameter duct supplied by others\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMobile home approval\u003c\/th\u003e\n\u003ctd\u003eApproved in the U.S. when installed per 24 CFR Part 3280; outside air kit, floor anchoring, spark arrester, and a listed mobile home chimney and connector kit are required; not approved for mobile home installation in Canada; not for installation in a sleeping room\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4\u003eEfficiency, Emissions, and Certification\u003c\/h4\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eHHV efficiency\u003c\/th\u003e\n\u003ctd\u003e77.7% weighted average across four burn-rate categories, measured using EPA Method 28R and CSA B415-10 methodology\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eParticulate emissions\u003c\/th\u003e\n\u003ctd\u003e0.54 g\/hr\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEPA certification\u003c\/th\u003e\n\u003ctd\u003eCertified to comply with the U.S. EPA 2020 particulate emissions standard, tested to EPA Method 28R, 40 CFR Part 60, using 19\" Douglas fir crib wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCertification report\u003c\/th\u003e\n\u003ctd\u003ePFS Report F21-673\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCO emissions by burn category\u003c\/th\u003e\n\u003ctd\u003eCategory 1 (low) 16.03 g\/hr, Category 2 (medium low) 24.7 g\/hr, Category 3 (medium high) 77.75 g\/hr, Category 4 64.51 g\/hr\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTested standards\u003c\/th\u003e\n\u003ctd\u003eConforms to UL Std. 1482-2022; certified to ULC Std. S627-2023\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eClearances and Hearth Requirements\u003c\/h3\u003e\n\u003cp\u003eThe values below are from the current Mansfield 8013 owner's and installation manual (revision 10\/21\/24). Reduced rear clearances require the HearthStone rear heat shield, kit 90-68210. Close-clearance connector pipe must be tested to UL standards and listed; double-wall figures shown by HearthStone are specific to Simpson Dura-Vent DVL and may vary with other brands. Dimensions are measured from the edge of the cast iron of the stove unless otherwise indicated.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Clearance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eSide, parallel installation\u003c\/td\u003e\n\u003ctd\u003e23\" (59 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e19\" (48 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eCorner installation — stove body to corner wall\u003c\/td\u003e\n\u003ctd\u003e14\" (36 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe, no rear heat shield\u003c\/td\u003e\n\u003ctd\u003eCorner installation — chimney connector to corner wall\u003c\/td\u003e\n\u003ctd\u003e26.5\" (68 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eSide, parallel installation\u003c\/td\u003e\n\u003ctd\u003e23\" (59 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e6\" (16 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eCorner installation — stove body to corner wall\u003c\/td\u003e\n\u003ctd\u003e14\" (36 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSingle- or double-wall connector pipe with rear heat shield 90-68210\u003c\/td\u003e\n\u003ctd\u003eCorner installation — chimney connector to corner wall\u003c\/td\u003e\n\u003ctd\u003e26.5\" (68 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear exit configurations\u003c\/td\u003e\n\u003ctd\u003eRear, parallel installation\u003c\/td\u003e\n\u003ctd\u003e19\" (48 cm) without rear heat shield; 6\" (16 cm) with rear heat shield 90-68210\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eChimney connector clearances\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Clearance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo rear heat shield\u003c\/td\u003e\n\u003ctd\u003eConnector to rear wall\u003c\/td\u003e\n\u003ctd\u003e19\" (48 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNo rear heat shield\u003c\/td\u003e\n\u003ctd\u003eConnector to ceiling\u003c\/td\u003e\n\u003ctd\u003e21\" (53 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWith rear heat shield 90-68210, or with blower kit shield\u003c\/td\u003e\n\u003ctd\u003eConnector to rear wall\u003c\/td\u003e\n\u003ctd\u003e6\" (16 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWith rear heat shield 90-68210, or with blower kit shield\u003c\/td\u003e\n\u003ctd\u003eConnector to ceiling\u003c\/td\u003e\n\u003ctd\u003e8\" (20 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eAlcove installation, unprotected surfaces\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Dimension\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMinimum alcove width\u003c\/td\u003e\n\u003ctd\u003e74\" (188 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMaximum alcove depth\u003c\/td\u003e\n\u003ctd\u003e43⅛\" (110 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAlcove, unprotected surfaces\u003c\/td\u003e\n\u003ctd\u003eMinimum alcove ceiling height from floor\u003c\/td\u003e\n\u003ctd\u003e73.5\" (187 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eFireplace and mantel installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation Configuration\u003c\/th\u003e\n\u003cth\u003eMeasurement\u003c\/th\u003e\n\u003cth\u003eRequired Clearance\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eFireplace installation, unprotected combustible surfaces\u003c\/td\u003e\n\u003ctd\u003eAbove stove\u003c\/td\u003e\n\u003ctd\u003e36\" (91 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFireplace installation, unprotected combustible surfaces\u003c\/td\u003e\n\u003ctd\u003eSide trim\u003c\/td\u003e\n\u003ctd\u003e14\" (36 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMantel with heat shield 94-79700\u003c\/td\u003e\n\u003ctd\u003eAbove stove\u003c\/td\u003e\n\u003ctd\u003e12\" (31 cm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eHearth and floor protection\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCombustible flooring must be protected with a covering of noncombustible material. The Mansfield 8013 does not require an insulated hearth pad and there is no R-value requirement; the requirement is ember protection.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eCountry\u003c\/th\u003e\n\u003cth\u003eMinimum Floor Protection\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003ctd\u003e40\" x 34\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCanada\u003c\/td\u003e\n\u003ctd\u003e49½\" x 41\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eHearthStone notes that luxury vinyl plank and luxury vinyl tile flooring warrants extra consideration, as some products begin to warp at 110° Fahrenheit, and that additional shielding may be necessary depending on the flooring used. Clearances to combustible surfaces may be reduced using an NFPA 211 approved wall protection system with the additional approval of the regulatory authority having jurisdiction.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation notice:\u003c\/strong\u003e Clearances and hearth requirements vary by connector type, shielding, and installation configuration. Refer to the current Mansfield 8013 installation manual and applicable local requirements before installation.\u003c\/p\u003e\n\u003ch3\u003eIncluded Equipment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMansfield Model 8013 woodstove with catalytic combustors installed\u003c\/li\u003e\n\u003cli\u003eOwner's manual with installation and operating instructions\u003c\/li\u003e\n\u003cli\u003eRemovable bypass handle\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Accessories\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eAccessory\u003c\/th\u003e\n\u003cth\u003ePart ID\u003c\/th\u003e\n\u003cth\u003eMSRP\u003c\/th\u003e\n\u003cth\u003eCompatibility or Requirement Note\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutside Air Starter\u003c\/td\u003e\n\u003ctd\u003e90-53220\u003c\/td\u003e\n\u003ctd\u003e$109\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage. Required for mobile home installations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBlower\u003c\/td\u003e\n\u003ctd\u003e90-57210\u003c\/td\u003e\n\u003ctd\u003e$599\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield, Heritage, and Castleton. Requires the rear heat shield, which provides attachment for the blower.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAsh Pan\u003c\/td\u003e\n\u003ctd\u003e90-54240\u003c\/td\u003e\n\u003ctd\u003e$599\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRear Heat Shield\u003c\/td\u003e\n\u003ctd\u003e90-68210\u003c\/td\u003e\n\u003ctd\u003e$129\u003c\/td\u003e\n\u003ctd\u003eFor Mansfield and Heritage. Required for reduced rear clearances and for blower installation.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eAll accessories listed above are optional and sold separately unless expressly stated otherwise.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eHearthStone warrants the appliance to the original retail purchaser only, when purchased by that purchaser and installed by an authorized HearthStone dealer or their designated representative, against defects in material or workmanship. Coverage begins on the date of the original invoice and is not transferable to subsequent owners.\u003c\/p\u003e\n\u003cp\u003eWarranty periods differ by component. HearthStone defines the term \"Limited Lifetime\" as 10 years from the beginning of warranty coverage, and applies it to the stone, to cast iron not listed elsewhere, and to the clean-burning air supply system. Door handles and latches and steel components and the firebox carry a 5-year period. Appliance electrical components carry a 2-year period. Enamel finish against peeling or fading, glass, the ash grate, accessories, and all components not listed elsewhere carry a 1-year period. The catalytic combustors are covered directly by the combustor manufacturer, Applied Ceramics, under a separate limited warranty that provides free replacement within two years of purchase and prorated replacement pricing thereafter.\u003c\/p\u003e\n\u003cp\u003eHearthStone pays for warranty labor performed by an authorized dealer during the first year after the purchase date only when the appliance was installed by an authorized dealer or their designated representative; otherwise, and thereafter, labor is the purchaser's responsibility. Exclusions include over-firing, improper installation or operation, service by anyone other than an authorized dealer, use of unapproved fuels or components, water and corrosion damage, and normal wear parts such as paint, gaskets, baffles, refractory materials, ash grates, and glass. Surface and hairline cracks and scratches in the stone that do not affect operation or safety are excluded, and HearthStone's obligation does not extend to the appliance's ability to heat a desired space. Warranty registration is not required as a condition of coverage. Refer to the complete warranty in the current Mansfield 8013 owner's manual for the full terms, conditions, and limitations.\u003c\/p\u003e\n\u003ch3\u003eAbout HearthStone\u003c\/h3\u003e\n\u003cp\u003eHearthStone Quality Home Heating Products builds wood- and gas-burning hearth appliances in Morrisville, Vermont, and has been building industry-leading products since 1978. Its stoves are handcrafted by Vermont craftsmen from materials including heating-grade soapstone, cast iron produced at the company's own foundry in Spain, precision-made steel, and engineered ceramics, and every HearthStone soapstone stove is signed by the stove builder. The company's TruHybrid™ system, used across its current wood stove line, adds catalytic tertiary combustion to primary and secondary combustion.\u003c\/p\u003e","brand":"Hearthstone Stoves","offers":[{"title":"Default Title","offer_id":53592140874004,"sku":"8013","price":5049.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0809\/9381\/2756\/files\/Mansfield8013_200214.webp?v=1785933061","url":"https:\/\/cozyglowstoves.com\/products\/hearthstone-stoves-mansfield-freestanding-wood-stove","provider":"Cozy Glow Stoves","version":"1.0","type":"link"}